Bug: Tool settings number boxes are cut off

Want to submit a new feature, an enhancement ? Do it here !
Post Reply
DerekCurrie
Posts: 2
Joined: Wed Jan 04, 2017 3:16 am

Bug: Tool settings number boxes are cut off

Post by DerekCurrie » Wed Jul 03, 2019 11:27 pm

This is a bug report, rather than a request. I can't imagine this problem was intentional.

Most of the tools have number setting boxes that are too small to read in Graphic Converter v11 (4003). As a result, the intended ability for fine tuning is lost. Here is what I have found:

1) Eraser has its setting cut off after two digits and the decimal point. In the screenshots attached:

'Eraser number is cut off (a).png' demonstrates how the numbers past the decimal are lost for the top setting.
Eraser number is cut off (a).png
Eraser number is cut off (a).png (53.65 KiB) Viewed 45 times
'Eraser number is cut off (b).png' demonstrates how two clearly different settings still show the same cutoff number of "14." Compare the thumb sliders of each. They are not aligned. Short of pasting in or deleting then typing in a specific setting for each, the user can't know their actual setting numbers.
Eraser number is cut off (b).png
Eraser number is cut off (b).png (58.07 KiB) Viewed 45 times
2) Stamp has a similar problem where the Radius box is not quite long enough to clearly show the last digit. This is illustrated in the screenshot attached: 'Stamp number is cut off.png'.
Stamp number is cut off.png
Stamp number is cut off.png (54.23 KiB) Viewed 45 times
3) Smudge has a similar problem where the box is not long enough to clearly show the last digit. This is illustrated in the screenshot attached: 'Smudge number is cut off.png'.

[The board interface refused to attach further images]

4) Magic Pen has the same again, as seen in the screenshot attached: 'Magic Pen number is cut off.png'.

[The board interface refused to attach further images]

5) Eyedropper has the same again, as seen in the screenshot attached: 'Eyedropper number is cut off.png'.

[The board interface refused to attach further images]

The other tools with settings number boxes are fine, from my observations, for the numbers they hold.

Please enlarge all of these boxes in order to allow observation of their precise settings.

Thank you!

[I'll attempt to attach the refused images in a reply post. If that fails, I'll hang onto them for a brief time, available upon request via email, etc.]

User avatar
forum_adm
Site Admin
Posts: 585
Joined: Fri Dec 23, 2016 9:41 am
Location: Germany
Country: Germany
Contact:

Re: Bug: Tool settings number boxes are cut off

Post by forum_adm » Thu Jul 04, 2019 8:57 am

Hi,

thanks for your report.

Please download the latest BETA at:
http://www.lemkesoft.org/beta.html

That should fix it.

Thorsten

DerekCurrie
Posts: 2
Joined: Wed Jan 04, 2017 3:16 am

Re: Bug: Tool settings number boxes are cut off

Post by DerekCurrie » Thu Jul 11, 2019 8:20 am

Thanks Thorsen. However, Fill and Eyedropper in v11.0.1 beta still have settings boxes that are too small. I've attached two screenshots:
GC 11.0.1b Eyedropper setting box too small.png
See image title
GC 11.0.1b Eyedropper setting box too small.png (31.91 KiB) Viewed 14 times
GC 11.0.1b Eyedropper setting box too small.png
See image title
GC 11.0.1b Eyedropper setting box too small.png (31.91 KiB) Viewed 14 times
Thanks for working on it!

:-Derek Currie
Attachments
GC 11.0.1b Fill setting box too small.png
See image title
GC 11.0.1b Fill setting box too small.png (47.52 KiB) Viewed 14 times

macvf
Posts: 49
Joined: Fri Dec 30, 2016 11:14 am
Location: Toulon
Country: France
Contact:

Re: Bug: Tool settings number boxes are cut off

Post by macvf » Tue Jul 16, 2019 12:29 am

Hi Dereck,

Thorsten, will fix that in a couple of day, please stay tuned ;-)
Philippe

French GraphicConverter localizer since 1994
Mac V.F. manager
French GraphicConverter forum administrator
English GraphicConverter forum administrator

Post Reply